Full transcript of “Chem1811 Echem lab 1 LabTalk”. Click a timestamp to open the video at that moment. Need another video? Use the YouTube transcript generator.
0:04 good day everyone welcome to another laptop for chem1811 in this experiment we'll be looking at galvanic cells and let us begin so we're going to be talking a lot about redox process and we should appreciate that almost all reactions in chemistry involve some amount of electron transfer or electron shearing as a case might be and when we look at the reaction if an atom or molecule gain electron we said that that specie is reduced and we call it process reduction now reduction is therefore accompanied by a reduction in the formal charge of the species meaning the charge assigned to that atom or molecule becomes more
0:51 negative the converse is also true where if in a reaction a specie lose electron then because we said that species oxidized and we call the process oxidation similarly when oxidation occurs the formal charge on that species is an atom or a molecule becomes more positive or increases if we should recall the first law of thermodynamics which looks at the conservation of energy which you can also talk about in Mass anything is always conserved anything in related to energy is conserved it therefore means that if we are going to be talking about a reduction and oxidation the two must occur simultaneously meaning if one specie is
1:39 being oxidized another species must be reduced because we have to maintain electroneutrality as a charge must be conserved therefore the two processes occurred together and we combine the two processes the reduction and oxidation and we call it redox all right or some people might say redox whatever it is however you want to pronounce it but the accepted pronunciation is redox and the two occurs simultaneously even though we might look at them independently we must always remember that both occur at the same time now another important concept when we're looking at electrochemistry is a concept of an electrolyte because in a solid phase electrons carry the charge but when we're in solution
2:24 it's ions in solution that will be carrying the charge so we need to cut understand what an electrolyte is and that is a substance which either completely or partially dissociates or put in a solvent to produce ions and it is these ions that can conduct electricity in the condensed phase in the theory you'd have come across two types of cells so there's a typhoid which is a galvanic or voltage depending on where you are in the world one terminology is preferred over the other and in your type 1 cell essentially you have authority electrical energy and these are used as batteries then type one cell
3:10 whenever you close a circuit the electric chemical reaction proceeds spontaneously and out of this you can use that electrical energy to do work so you can drive your electronic devices you can use it to dry the other cell which you are when they look at briefly but you can use that electrical energy to do work here's the type 2 which is the electrolytic cell and this requires an external energy source to drive the electrochemical reaction and as a consequence the difference between a type 2 and a type 1 is that in a type 2 electrochemical reaction does not proceed spontaneously because it requires this external source for example if you were to produce aluminum metal from The Ore aluminum or
3:56 bauxite it requires that you do electrolysis and it's very energy demanding a direction doesn't occur getting aluminum from aluminum three doesn't that corresponding so we're going to be focusing on the type 1 cells or galvanic cells that's what the experiment today you will be looking at so we're going to explore these type 1 cells the theory behind it a little bit more to quite a simple case if we were to dip a piece of zinc metal into a copper II solution we notice a series of observation first over time we see this brown metal depositing on that strip of zinc and the blue solution color Fades then
4:42 eventually it goes colorless we can clearly see that the chemical reaction is occurred how can we break the stone into smaller pieces and describe the chemistry of what's going on secondly interaction is spontaneous can we control the reaction so just as I only did the zinc in this we get an immediate reaction what if we were to control this reaction by separating the components of this reaction mixture and see if we can use it to get electricity or you know get some work out of it the answer is yes we can do that so if the reaction occurs spontaneously we can construct an electrochemical cell out of it what we would do is for example this zinc electrode we would create a half
5:28 cell using this so we'll have the zinc electrode in some zinc electrolyte and then the other half fraction is involves copper would have a copper electrode in some copper electrolyte and then in order for us to complete the circuit we would use what we call a sawbridge so with your solid Bridge electrons do not travel through the salt bridge the salt bridge is there to maintain electroneutrality so ions will either enter or leave the salt bridge based on whether we are using up or providing excess of a particular charge on one side of the half cell so by convention the left hand side contains the anole and in a galvanic cell because the animal is supplying electrons by
6:15 convention is negatively charged and it is the site of oxidation Again by convention the right hand side contains a cathode and a cathode because it's accepting electron it behaves as an electron sink is positively charged and it is the site of reduction now they'll tell you that electron flows in The Wire the reality is that it's an electric field but that's a story for another type but at the end of the day there is a general migration over time of electrons from the anode to the cathode let's keep it simple I'll leave it at that okay so what about the galvanic cell let us try and break down that same reaction
7:02 now into two half cells so we have the zinc half cell on one side we have the copper half cell on the other side and we have connected them using a sawbridge and we can stick a circuit between the two so you could pour a light bulb for example or if you just want to measure the potential difference we could use a voltmeter or if you wanted to measure current of course you could insert an ammeter in that circuitry let us break this zinc dipping the zinc into copper into two half cells and see how we can break the stone into Redux and our redox processes from our observation we saw that the zinc was being edited which means that we're forming zinc ions from the metallic zinc and therefore
7:48 that's an oxidation process zinc in its Elemental state is a zero charge when they give out zinc two plus we have increased the oxidation state so we have caused oxidation and the process we have given up two electrons so this oxidation refer to it as a zinc coupled so zinc to zinc zero and then you have the other half cell which was the copper ions being deposited as a metallic copper and going from the copper two plus to neutral copper which is the elemental state that again would require two electrons so the two electrons being supplied by the zinc is accepted by the coupler to form Elemental copper whereas the zinc element goes to form zinc ions on the anode here which is a zinc it is
8:34 being oxidized form in zinc ions and at the cathode copper is being deposited if we were to break this into two half reactions to complete a cell so this way we could control the reaction so we could have a switch in the circuit and when we close the switch Direction and proceed and if we open and switch the reaction stops but when we dip the zinc directly into the copper Direction proceeds until everything is consumed or you will manually remove the strip of zinc from the solution understanding how to disaggregate a government extend into the two half cells means that we can use it to figure out how to create different batteries depending on the needs we have
9:21 so notice in both cases the Redux couple is denoted an oxidized form slash reduce form and this is so going back to a concept that we'll look at shortly that deals with how we write the standard reduction of these species but you will note in the literature Redux couples are always written oxidized form slash reduced form it doesn't matter whether it is an oxidation or reduction that's how we write them now previously I mentioned the fact that the salt which is there to maintain electroneutrality how do the salt which work the salt which consists of a neutral electrolyte neutral meaning that it does not interact with any other species we are generating either from oxidation or reduction so it doesn't
10:08 participate directly in any chemical reactions and it's a high concentration because it should Supply ions on demand for example on the anodic side here we're generating zinc ions which means that if there is nothing extra coming from the zinc solution here we have had the counter ion to balance the salts if we were using zinc chloride for example or zinc sulfate we would have had the exact amount of anions in here to balance the charge based on the amount of zinc ions we have initially in this electrolyte solution so if oxidation proceeds and we are generating more zinc cations there must be another speech there to balance this buildup of charge because nature must remain Electro neutral and
10:54 if you have an unbalancing charges it's going to present problems so the purpose of the solid bridge is that on this side where the zinc ions are being generated the anion of the salt in the salt bridge will come into the solution to balance that charge you might be wondering okay if anions are moving from the solar bridge what about the cations that remain this is where the other side of the reaction comes into play because if you notice if we are going to be depositing copper on this electrode we are removing cations from the solution here so the cations that balance charge of the salt of the anions in this salt bridge here those cations will migrate into the solution to replace the copper ions that are being removed from the
11:41 solution so we maintain that electroneutrality so we pumping negative charges on this side to balance the cations that are being generated are we pumping positive charge on this side to replace the cations that are being removed for maintain electroneutrality using that software so it has to be of a high concentration of your electrolyte and it must be inert meaning that it doesn't react to form in soluble material for example any species that we have in solution so the choice of the salt which is important based on what we are reacting as I pointed out once we have disaggregated the electrochemical set into half reactions we can control the process so just like your battery a double AR Triple A
12:28 battery battery or any other battery it stores the energy until you close the cells when you put it in a circuit and close the circuit so that current is able to flow that's when your action occurs and it goes on until you have reached aerodynamic equilibrium and the battery is there so if we have these two half processes when we combine them one process is being oxidized always been reduced when we combine the two processes overall the electrons will cancel because one side produces electron and the other side is accepting electron and overall the electrons will cancel and we will end up with a balanced redox reaction you'll notice also that oftentimes the counter ion is not included because the
13:13 counter ion will be on either side of the equation and they will also cancel out so we'll just focus on the ionic equations when we're dealing with these electrochemical reactions remember when we are writing this standard schematic notation for our electrochemical cell IUPAC recommends that we put the anode on the left hand side and a cathode on the right hand side an electron move from left to right in that manner now depending on the conditions that we employ if we Empower what we call the standard conditions and in thermodynamics the standard condition implies that we have
13:58 one molar technically should be one unit activity one molar concentration if we have gases involved they're at one bar pressure and the temperature being 25 degrees Celsius then we would have the cell of the standard conditions and the potential that we measure will be called the standard cell potential and as I pointed out for any electrochemical cell we can write two half reactions associated with the processes occurring so the reduction and the oxidation processes we can combine different pairs of half cell to measure different cell potentials now this random combination how do we determine which half cell is
14:46 most likely to be reduced or oxidized in fact how do we arrive at the potential for any so-called half reaction as you have learned in the theory portion of the course we use the standard hydrogen electrode as our reference electron so that electrode is set at zero and then we measure other half reactions relative to it and a table is established so this is a very abbreviated form of our standard reduction potential but the longer shorter visit is at the reduction of proton for hydrogen is set at zero and we measure other potential relative to it some can be more positive some can be more negative what does this mean
15:32 if we were to set actually as our reference so we're saying that this process here is zero and we measure everything else to it we made a series of values and how do we calculate the cell potential if we say electron star here I end up over here with any thermodynamic Parliament so we want to measure change we talk about the final Place minus the initial state or place and then we do with that subtraction the change in any thermodynamic parameter X that changes in by Delta X it is the final value minus the initial value and a consequence of this set we can have positive and negative value depending on whether
16:19 one value is larger than the other and the Order of subtraction quite naturally so if we should translate this to uh chemical electrochemical cell that change in potential because you cannot measure an absolute potential we always measure a potential difference that difference in potential which is the cell potential would be where the electrons stop which is at the cathode minus where it's coming from which is the anode so our cell potential is calculated as the potential for that the standard reduction potential for your cathode minus the reduction potential of the anode or E anode and this is how we calculate the cell potential so once we know the value for each half cell we just simply do the
17:05 subtraction the F1 minus the node and we're able to calculate the cell potential now this means that we can have negative and positive potential and as we saw what we're using is she as a reference there were negative and potential values you can think about that electrochemical scale adjust us how we use sea level at zero for Gravity so sea level is chosen at zero it's an arbitrary reference point and it doesn't mean that if an object is placed in C or at sea level and you put it in a c it will not sink because gravity still acts upon it it's just a reference point for calculation purposes and this means that if we have a potential that is negative
17:51 simply means that a relative to the standard hydrogen electrode well not those potential standard reduction potential let me recap so if we have a negative standard reduction potential it doesn't mean that direction doesn't occur means that are relative to the sheen instead of accepting electrons it would rather to give it up to the Sheep so in other words the she will now be forced to become the capital one when you connect that half cell so the sign is just a matter of which direction the electron is going in that case okay so if we have two half cells and they are both measured relative to the standard hydrogen electrode if we want the process to be spontaneous
18:37 we must obtain a negative Gibbs free energy and the only way we can get that negative Gibbs free energy is if the cell potential is positive this is so because we will appreciate that the glittery energy Criterion is that Delta G for a cell is equal to negative number of mole of electron transfer these constant times the cell potential and this means that if we have a positive cell potential so if e sub is positive the Delta G is going to be negative and hence the process will be spontaneous in
19:23 the direction written so if we want to figure out how to set up a cell to get a spontaneous electrochemical process it means that the cathode reduction potential must be more positive than the anode reduction potential so when we do the subtraction here we get overall a positive value so in other words positive cell potential and hence a spontaneous reaction as written let's put that into practice we need to remember that e0 by definition is the standard reduction potential and hence it will be written exclusively as a reduction so we're
20:09 going to have an oxidized form custom electrons give us the reduced form and if we are given two half reactions and the corresponding standard reduction potential we can use this to construct a galvanic cell and remember in a galvanic cell the Criterion is that the reaction should proceed spontaneously and hence it must have a positive cell potential so we can use that knowledge to figure out which of these two heart cells will be the anode and which will be the cathode and we stated that in order for us to get a positive cell potential we need to identify the cathode which must be more positive than the anode so if we look
20:55 here we see that plus 0.34 is obviously more positive than negative 0.76 so this half reaction must be the cathode so we identify copper as our cathode and if this is a cathode then this other half reaction must be the anode and you would simply rewrite this equation to represent oxidation and you can combine it to get your two heart cells all right all we need to do is to identify the reduction potentials or the standard reduction potentials and if we're going to create a galvanic cell under standard conditions the one that is more positive must be our cathode and the other half reaction must be the anode so to calculate e0 for this cell it's
21:40 simply the cathode minus the annual and we see here we get the positive 0.34 minus the negative 0.76 and we get positive 1.1 volt so positive cell potential if we construct this cell with copper B in the cathode zinc being an animal we should get a positive cell potential which means that that reaction would proceed spontaneously if you do it the other way around making copper the anode and zinc the cathode it would no longer be a galvanic cell you have been constructing an electrolytic cell and in order for that reaction to proceed spontaneously you would need to supply external energy because you would have ended up with a negative cell potential which would mean it's non-spontaneous in terms of the
22:25 gives free energy okay so that summarizes these a part of the theory the other part we need to look at is what happens when we how to balance equations when we're using a standard reduction potential as I pointed out it's quoted exclusively as a reduction the other thing about this the value is that you get relative to the she is that it is independent of the number of moles of electrons meaning if I am going to be balancing two half equations and for example let's say I need to multiply this value by 4 to balance the electrons which balances the charges in the reaction irrespective of what I do to balance in
23:13 this equation so if I need to multiply it by 2 4 3 or any number the standard reduction potential does not change because this value as the name suggest is measured under standard conditions manipulating a half reaction is just to balance charges because this is only a half reaction if there's another half reaction that requires eight electrons then in order to combine these two half cells I would have to balance the charges so that to multiply this half fraction by some Factor but the reduction potential does not change that's very important unlike when you're doing your thermo chemistry when you're playing around it this is law for example where you would
23:59 multiply the enthalpy by some Factor based on how much you multiply the the reaction by when you're doing electrochemistry the e0 values are unaffected by whatever Factor you need to multiply the half cell by the balance charge that is very important okay hello we have looked at this schematic representation for these half cells obviously drawing this all the time is going to be cumbersome but there are shorthand notations by which we can represent the same diagram here and the same cell reactions for this reaction here we have zinc reacting with copper ions to give us
24:44 zinc ions and copper solid we can see that zinc is being oxidized so that zinc would represent our annual so we simply represent this as zinc went to form zinc two plus so this vertical bar here represents a phase transition so a solid to liquid phase transitions we have zinc solid going to zinc aqueous solving it right so there's a solid liquid phase transition here it could also be for a solid gas or a gas liquid the same process that applies a bar represents a phase difference on the other side of the cell so we have the zinc when the zinc ions on this side on the other side we have copper ions being deposited to form copper metal as you can see here copper going to form
25:30 copper solid so that's the reduction process that's the other part of the half cell so we have a copper ions going to form copper and again there's a difference in the face we have aqueous liquid going to Sunny so there's a phase boundary here between these two cells we have they are separated by a third Bridge so what we have is a double bar here to represent this separation and the salt bridge so notice this is very similar to how you actually draw the cell on one side you have the annual compartment which is the electrode and electrolyte on the other side you have the cathode compartment which is the cathodic solution being deposited on the cathode
26:15 so when we write our standard cell notation it is reflecting the schematic representation that we would have actually drawn using anupac notation with the anode on the left cathode on the right and as I pointed out earlier on so this diagram here illustrates it even further as a cellular reaction progresses notice the zinc and what is being h decreasing in size and a copper electrode or the cathode here is increasing in size metallic copper has been deposited deposited on it and that's the reason why you need the salt bridge to balance these charges that are being added to one side and depleted from the other side right okay so this is how we represent the shorter notation it's just like
27:02 drawing the schematic representation now what happened if we do the reaction on the non-standard condition because you will always have standard values when you are when you're out in the field if you need to make a battery if you need to design a battery for a certain cell potential you won't necessarily need or have standard conditions at all times so I don't understand the conditions we can still predict the potential of the cell given our knowledge of thermodynamics so knowing that it gives free energy is related to other parameters so the Gibbs free energy relates the enthalpy and entropy of the system
27:48 and there are other thermodynamic relationships governing the giftware energy for example here the Gibbs free energy under any condition is related to The Standard Value Plus the deviation from standard conditions so this portion here involved in a natural log and this parameter here Q which is the reaction quotient these can tell us the relationship between the expected value or the value on any condition which relation to the standard condition so we know that next gives free energy gives us a maximum work that can be done by the cell and this work is used to run yourself for the flashlight whatever it
28:33 is and we appreciate that it gives free energy is related to the cell potential by this relationship we can see that if we know it gives free energy we can use this relationship and make it the substitution to identify how the cell potential should vary once we deviate from standard condition because at equilibrium here at equilibrium Q becomes k and if we talk about standard cell conditions as you'd see if all of these concentrations are one then Q or k becomes one and natural log or log of in in F1 whichever log to the base you're using it becomes zero and all that is
29:19 right on portion disappears therefore understand that condition it gives free energy is equal to the standard value so if we should deviate from standard condition we can relate the cell potential to the standard value by substituting Delta G in this equation and we would arrive at the famous learns equation pronounce equation tells us what the value should be under any condition if we measure it under standard condition this right hand side would work out to the zero and the measured value will be equal to the standard value but if you should vary from standard condition this will have a non-zero value and you can either
30:05 increase or decrease the cell potential relative to the standard value so this is important for us to learn this equation we will be using this in the lab course to do some calculation at some point all right so hopefully you can note you can see that when we're talking about State functions a state function lead us back to thermodynamics one thermodynamic relationship can lead to several other equations that can be useful for calculating parameters that you didn't even think about initially right so we can see e cell can give us a lot of information it can provide us
30:51 information about Gibbs free energy and the fact that gives free energy is related to enthalpy and entropy we can also use this to determine entity and entropy parameters for a cell okay let us put this into practice if we have a general equation for the nurse equation in terms of the natural log we can convert natural log to log to the base then by this conversion factor here of 2.303 so this equation and this equation is the same where does converting from log to the base e to log to the base 10. now you'll notice there are a lot of standard values here or constants so we have the universal gas constant we have Faraday's constant
31:36 if the temperature is room temperature which is 298 Kelvin these three values are constant and they work out to give you 0.0592 so at 25 degrees Celsius or 298 Kelvin the cell potential is related to The Standard value by this function and I pointed out earlier on that 2 is the reaction quotient which represents the cell under any condition when a system reached equilibrium the quotient becomes the equilibrium constant and therefore we can rewrite the nurse equation in terms of an equilibrium constant let us use this to calculate for example
32:23 the cell potential for this cell so on the left hand side we have the anode on the non-standard conditions because notice the concentration here is 0.01 molar and on the right hand side we have the shield so we have one molar acid hydrogen gas at roughly one bar where the Platinum electrode Crystal reaction as you can see here would be cadmium being oxidized to cadmium two plus and of course protons be reduced to hydrogen so we can write over our cell reaction just from looking at this shorter notation and if the measured potential on a standard condition is your cell is 0.4 what is the cell potential under these
33:10 conditions so here we can see two direction quotient which is written just as how we write we would write a equilibrium constant would be the products of the reaction raised to their respective coefficient divided by the concentration of the reactants raised to their respective coefficients product side we have cadmium ions we have hydrogen so we use the partial pressure to represent this gas on the reactant side we have cadmium as a metal and we know that pure solids and pure liquids are not included in our reaction quotients or equilibrium constants because we cannot vary their
33:55 concentration so in the denominator we will only have hydrogen because this is a solvated specie and of course that concentration can be varied and we have two of it says h plus raised to the power of two so we can calculate a quotient by plugging in the concentrations given to us here so we have the cadmium concentration the partial pressure of the hydrogen which is one atmosphere and the concentration of protons squared and we get a quotient here of point zero one this therefore means that if we apply the nerves equation we're trying to find e cell we have e0 cell which is 0.4 and we have this ratio here so 0.0592 divided by the number of
34:40 electrons involved as we can see this is a two electron process so that's two log the reaction quotient and therefore you can calculate the spell quite easily done we will be applying a similar scenario in the lab when we have vary the concentration of the electrolyte in one of the half cells we will use the standard value and calculate the expected value and compare that to the value we actually measure okay here's another example calculate the potential for the following cell as it is written so you want to calculate this so we have zinc Point using two plus this is the concentration of zinc two plus we have
35:27 copper ions go into metallic copper calculate the cell potential and tell us if it is spontaneous size is written now how would you know if it is spontaneous again when you calculate e cell and negative e cell means it's non-spontaneous positive e cell will tell you that this is spontaneous and that's the criteria you'd use to determine if the reaction is spontaneous as given onto the experiment so we have summarized the basic fears needed onto the experiment let's put this in practice the experiment has a few objectives you want to construct some galvanic cell investigate the chemical reactions that take place in this galvanic cell
36:14 identify how you can combine electrodes and electrolytes to give you different types of galvanic cell and ultimately determine the potential of these cells that you have constructing and of course we would also want to investigate if we deviate from standard condition how is this related to the violence predicted using the Learned equation so the first procedure we're going to be investigating the relative reactivity of the the metals and the respective electrolytes so you're asked to dip a strip of metal salt solution of another metal and you repeat these two different sort of combination meaning you for example the zinc
36:59 electrode in the copper solution you would put the magnesium in the copper and you also put magnesium in zinc Etc if you leave for example if you leave the zinc in a cup for a long period of time you start to have excessive deposit of copper on the zinc and deteriorate the copper solution meaning you convert copper two to zinc solution and if you're going to reuse that electrode you would have to polish off this copper so what I'm going to ask you to do is do not leave it in the solution for too long a time period if you notice any change record that change and immediately
37:46 remove the electrode from the solution right because they do not want to have to do excessive polishing of the electrode between experiments you see an observation quickly required observation and remove the metal from that salt solution to prevent a scenario like this where you have transformed most of the zinc into copper right having copper being Electro deposited on the zinc if you want to reuse the selection as I stated you'd have to do some serious cleaning you have a mechanically remove this copper and then sand down and polish that zinc electrical to use it again we have limited resources we don't want to have a scenario like this so please be mindful of that
38:32 now once we have made these observations we need to complete the table in your manual so again you would State what happens for the different combination for example if you put a copper electrode in a copper solution you will not expect to see a reaction if you place a zinc electrode in the copper solution as stated you start to see that brown deposit on the electrode and over time the color of the value if I should feel if you are to place magnesium in that copper solution again you would make note of the observation if you were to place copper in a zinc solution Do You observe any change zinc in a zinc solution Do You observe any change if you put magnesium in zinc again do you observe any change now you'd want to make note for example if
39:19 You observe gas is being evolved because some of these electrochemical reaction might result in the evolution of gases so you need to make note of that as well all right so different electrodes in different electrolytes make an observation Do You observe any reaction next part is that you need to create half cells and you create a half cell by immersing the metal electrode into a salt of that electrode so for example you put the zinc in the zinc solution you put a copper in the copper solution and that would give you a half cell and we're going to be using the one molar Salt Solutions at this point because we're trying to do the
40:05 experiment on the standard condition so we're creating half cells reflecting in standard condition essentially as I stated here copper electron in that copper solution zinc electrode indexing solution and a magnesium electrode in that magnesium electrolyte now once we have created the half cells we're then going to combine these half cells or connect the half cells to get a actual cell and we're going to be measuring the potential now note in order for us to quote unquote construct a complete cell circuit we need one salt bridge we need to connect the electrodes and
40:53 we're going to have a voltmeter between the electrodes our high impedance voltmeter between these electrodes to measure the cell potential so this is a schematic representation this is what your setup will probably look like you're going to have the two beakers with the respective electrolytes and electrodes and we're going to have a filter paper soaked in either potassium nitrate or a potassium chloride saturated solution of nitrate or chloride and that will behave as our sawbridge so you need to have the filter paper inside this solution so it should be touching the two solutions immersed in both Solutions and you have your electrodes again inside the respective electrolyte and
41:39 then you would connect the two electrodes to the voltmeter to measure the cell potential but you do not want to have this going for a very long period because you'll notice the cell potential will decrease over time because you start to change the concentrations inside the two half cells so what you're going to do is when you're ready you connect the last terminal quickly record that potential and then disconnect the terminals all right that's important do not leave the circuit set up for extended periods because you would see a decrease in the potential over time so you're going to just connect quickly record the value and disconnect the terminals in other
42:25 words we are going to open the cell that way electrons don't flow continuously right so connect measure disconnect good and very importantly remember your cell is not complete without the salt bridge and the salt bridge will simply be a piece of filter paper soaked in a saturated solution of either potassium nitrate or potassium chloride the other part of the procedure then requires that you determine the cell potential under non-standard condition and here you it's recommend that you keep one half cell constant change a concentration of the other half cells so we have three halves of your
43:11 work in it we have the copper zinc and magnesium half cells so let us say for example you decide to keep the copper half cells constant and then this is your choice whichever one you want to keep constant it's up to you if you decided to keep the copper half cell constant so you'd have the one molar solution here and for the other half cell you would use the point zero one molar electrolyte here so let us say this is a zinc um half cell you keep the zinc electrode but you change the solution from the one molar zinc salt or the 0.01 molar and just as you did before you would connect the crocodile Eclipse to the electrode and measure the cell potential and again
43:58 as soon as you measure the cell potential disconnect so that it don't discharge the cell right and once you have done the zinc you will now replace this half cell with the magnesium for example so you have the Magnesium electrode with the point zero one magnesium electrolyte so that would give you the value now on the non-standard conditions all right so that's if you chose to use this as your reference so keep this one constant weird or others you could also keep the zinc constant but Verity copper solutions they use the 0.01 molar copper electrolyte here and of course we connect this to the magnesium and keep that at point zero one right so you can choose whichever
44:43 one you want to keep constant it's up to you or whichever one you're keeping constant leave that one as the one molar electrolyte that's important so again what you're gonna have here is three combinations so any example I've given you here where the copper is kept constant and you change zinc solution you keep the copper again constant and Vary the Magnesium concentration and of course you get a copper and point zero one molar copper so you'd have three bodies filled here if you decided to choose copper as the reference okay so once you have done that again here you would highlight which is the anode which is the cathode
45:28 word and of course there's that potential now you will determine this again based on the sign that you obtain when you connect the cells so if you obtain a negative potential here it means you need to reverse the order of these clips so you're changing the polarity and you need to record which side is positive and which side is negative because at all points for it to be spontaneous we need to have a positive self potential and that's pretty much the experiment once you have completed the experiment you're going to now complete the contents of the table that's the end of the laptop I'll see you next time